CraftKeepCraftKeep
Start free
Laser

A beginner's guide to laser cutting files

Laser files come as vector drawings, pictures for engraving and project files with your settings. Here is what each one is for and how to keep them in order.

By CraftKeep Team · · 5 min read

A laser cutter with its lid open over a wooden coaster being engraved, beside a box of wooden shapes and file cards.

Laser cutting files come in three kinds: line drawings the laser cuts or scores, pictures it engraves, and project files that remember your settings. This beginner's guide to laser cutting files explains each kind, which format to reach for, and how to keep the whole collection easy to find. Once you know the difference, a folder full of strange endings starts to make sense.

A new laser often comes with a few sample files, and then the downloads begin. Coaster sets, earring templates, box plans, ornaments. Each arrives as a ZIP with its own mix of formats. A little order early on saves a lot of searching later.

Cut lines, engraving and project files

Your laser does two main jobs. It cuts or scores along lines, and it engraves by burning a picture into the surface. The files you collect match those jobs:

  • Vector files hold lines and shapes. The laser follows them to cut or score. SVG, DXF, AI and PDF often hold vectors.
  • Image files hold a picture made of tiny dots. The laser engraves them row by row. PNG, JPG and BMP are common.
  • Project files hold the design laid out with your power, speed and layer choices, ready to run again.

Many designs mix them. A coaster file might hold a cut line around the edge and a picture to engrave in the middle.

Laser cutting files a beginner will see most

These are the endings you will meet most often:

Ending What it holds Good to know
SVG Lines and shapes The most common download for cutting and scoring
DXF Lines and shapes from drawing and CAD programs Often used for box and furniture plans
AI An Adobe Illustrator drawing Common in designer bundles
PDF Lines, pictures or both Also used for printed instructions
PLT / HPGL Plotter lines Older format some programs still use
PNG, JPG, BMP Pictures for engraving Photos and grayscale art
LBRN2 / LBRN LightBurn project files Your layout and settings

LightBurn's own guide lists AI, SVG, DXF, PDF and PLT/HPGL among the vector formats it imports. It also lists PNG, JPG, BMP, GIF, TIFF and other picture formats.

What a LightBurn project file keeps

When you save your work in LightBurn, it becomes a project file. LightBurn's guide says it saves as .lbrn2 by default, or as .lbrn, the older "LightBurn Legacy Project" format.

The guide also points out a detail worth knowing. If you import a .lbrn or .lbrn2 file into another project, you get the graphics but not the cut settings saved in it. Open the project instead when you want its settings back.

That makes your project files the record of what worked: which layers cut, which engraved, and the settings you chose for that wood or acrylic. Treat them as part of the design, not as scrap. Good LightBurn file management simply means saving each project next to the design it came from.

How to organize laser design files

A simple system works for ten files or ten thousand:

  1. Unpack each download into one folder or project. Name it after the item, such as "Mountain coaster set".
  2. Keep the original files and your project file together. The SVG the designer sent and the LBRN2 you saved belong side by side.
  3. Add a short note about materials. For example, "1/8 in birch plywood, cut layer twice, engrave at low power". Write down what worked for your machine.
  4. Group designs by the shop or designer. It keeps licenses easy to find, especially if you sell what you make.
  5. Tag by use. Words like "coasters", "ornaments", "signs" or "gifts" help you search later.
  6. Keep a test file with each material. A small test pattern and its notes save wasted boards.

Think of it as laser cutting file storage with labels, rather than one big pile of downloads.

For example, say you buy a set of four holiday coasters. Unpack the ZIP into a project called "Holiday coasters". Inside sit the designer's SVG and PNG files and the license. After your first run, save your LightBurn project there too, and add a note: "1/4 in cherry, engrave first, cut twice." Next December, everything you need is in one place.

Keeping a safe copy

Many people keep their laser files only on the computer that runs the laser. That computer sits in a dusty workshop, and drives fail. Keep your library somewhere that is backed up. Treat the workshop computer as a working copy you can replace at any time.

A laser engraving design library in CraftKeep

The Laser Gift Tags project: a wavy name tag SVG, a finger-joint box panel and a scalloped coaster, both DXF, shown as line pictures.
A laser project: SVG and DXF designs for a name tag, a box panel and a coaster, shown as line pictures.

CraftKeep is a laser engraving file organizer that keeps your designs in one online library. It works in your web browser on a computer, tablet or phone. Here is what it does with laser files:

  • Pictures for line files. SVG, DXF and EPS files show as a picture drawn from their lines, and so do PLT and HPGL plotter files. Images and the first page of a PDF get a picture too.
  • LightBurn projects are kept safely. LBRN and LBRN2 files are stored with their project and labeled "Cut or laser file". An LBRN2 project shows the picture LightBurn saved inside it; an older LBRN file shows a file icon. Keep the SVG or a PNG of the finished piece in the same project and you always see what it is. In that way CraftKeep works as a LightBurn project organizer beside the program itself.
  • ZIPs are unpacked for you. Choose Add files and pick your ZIPs. CraftKeep asks which designer and project they belong to, and keeps the designer's folders.
  • Notes and tags. Each project has Notes for your settings and materials, and up to 5 tags.
  • Search across everything. Search finds projects by designer, project name, tag, file name and the words in your notes and PDFs.

CraftKeep doesn't connect to your laser or to LightBurn. When you are ready to cut, open the file and choose Download, then open it in your laser software as usual.

Where to go next

Start with the designs you use most. Give each one a project, keep its project file beside it, and write one line about the settings. Your laser engraving design library will grow neatly from there.

To learn more, see the laser cutting file organizer page, the supported formats list, and searching your library. If you also own a vinyl cutter, read the beginner's guide to cutting machine files.

LightBurn is a trademark of LightBurn Software, LLC. Adobe Illustrator is a trademark of Adobe Inc. CraftKeep is not affiliated with these companies.

Sources

Try it with your own files

Make a free CraftKeep library and see your laser files as pictures you can search.

Topics:Beginner's guidesFile formats

Bring your designs into CraftKeep.

Every embroidery and craft design you own, shown as a picture and found by name.

No credit card needed